 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MC14538B Dual Precision Retriggerable/Resettable Monostable Multivibrator The MC14538B is a dual, retriggerable, resettable monostable multivibrator. It may be triggered from either edge of an input pulse, and produces an accurate output pulse over a wide range of widths, the duration and accuracy of which are determined by the external timing components, CX and RX. Output Pulse Width = (Cx) (Rx) where: Rx is in kW Cx is in mF Unlimited Rise and Fall Time Allowed on the A Trigger Input Pulse Width Range = 10 s to 10 s Latched Trigger Inputs Separate Latched Reset Inputs 3.0 Vdc to 18 Vdc Operational Limits Triggerable from Positive (A Input) or Negative-Going Edge (B-Input) Capable of Driving Two Low-power TTL Loads or One Low-power Schottky TTL Load Over the Rated Temperature Range Pin-for-pin Compatible with MC14528B and CD4528B (CD4098) Use the MC54/74HC4538A for Pulse Widths Less Than 10 s with Supplies Up to 6 V. http://onsemi.com MARKING DIAGRAMS PDIP-16 P SUFFIX CASE 648 SOIC-16 D SUFFIX CASE 751B TSSOP-16 DT SUFFIX CASE 948F 1 16 SOIC-16 DW SUFFIX CASE 751G 1 16 SOEIAJ-16 F SUFFIX CASE 966 Unit V V mA mW C C C MC14538B AWLYWW 14538B 16 MC14538BCP AWLYYWW 1 16 14538B AWLYWW 1 16 14 538B ALYW * * * * * * * * * AWLYYWW MAXIMUM RATINGS (Voltages Referenced to VSS) (Note 2.) Symbol VDD Vin, Vout Iin, Iout PD TA Tstg TL Parameter DC Supply Voltage Range Input or Output Voltage Range (DC or Transient) Input or Output Current (DC or Transient) per Pin Power Dissipation, per Package (Note 3.) Operating Temperature Range Storage Temperature Range Lead Temperature (8-Second Soldering) Value - 0.5 to +18.0 - 0.5 to VDD + 0.5 10 500 - 55 to +125 - 65 to +150 260 1 A = Assembly Location WL or L = Wafer Lot YY or Y = Year WW or W = Work Week ORDERING INFORMATION Device MC14538BCP MC14538BD MC14538BDR2 MC14538BDT MC14538BDTR2 MC14538BDW MC14538BDWR2 MC14538BF MC14538BFEL Package PDIP-16 SOIC-16 SOIC-16 TSSOP-16 Shipping 2000/Box 48/Rail 2500/Tape & Reel 96/Rail 2. Maximum Ratings are those values beyond which damage to the device may occur. 3. Temperature Derating: Plastic "P and D/DW" Packages: - 7.0 mW/_C From 65_C To 125_C This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, Vin and Vout should be constrained to the range VSS (Vin or Vout) VDD. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either VSS or VDD). Unused outputs must be left open. TSSOP-16 2500/Tape & Reel SOIC-16 SOIC-16 SOEIAJ-16 SOEIAJ-16 47/Rail 1000/Tape & Reel See Note 1. See Note 1. v v 1. For ordering information on the EIAJ version of the SOIC packages, please contact your local ON Semiconductor representative. Publication Order Number: MC14538B/D (c) Semiconductor Components Industries, LLC, 2000 1 March, 2000 - Rev. 3 MC14538B PIN ASSIGNMENT VSS CX/RXA RESET A AA BA QA QA VSS 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 VDD VSS CX/RXB RESET B AB BB QB QB BLOCK DIAGRAM CX RX 2 Q1 5 B Q1 RESET 3 CX RX 14 Q2 B Q2 RESET 13 RX AND CX ARE EXTERNAL COMPONENTS. VDD = PIN 16 VSS = PIN 8, PIN 1, PIN 15 10 9 6 7 VDD 1 4 A VDD 15 12 11 A ONE-SHOT SELECTION GUIDE 100 ns MC14528B MC14536B MC14538B MC14541B MC4538A* *LIMITED OPERATING VOLTAGE (2 - 6 V) TOTAL OUTPUT PULSE WIDTH RANGE RECOMMENDED PULSE WIDTH RANGE 1 s 10 s 100 s 1 ms 10 ms 100 ms 1s 10 s 23 HR 5 MIN. http://onsemi.com 2 MC14538B IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII ELECTRICAL CHARACTERISTICS (Voltages Referenced to VSS) VDD Characteristic Symbol VOL Vdc 5.0 10 15 5.0 10 15 5.0 10 15 VIH 5.0 10 15 IOH Source 5.0 5.0 10 15 IOL 5.0 10 15 15 15 -- -- 5.0 10 15 5.0 10 15 5.0 10 - 3.0 - 0.64 - 1.6 - 4.2 0.64 1.6 4.2 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 0.05 0.1 -- -- 5.0 10 20 2.0 2.0 2.0 - 2.4 - 0.51 - 1.3 - 3.4 0.51 1.3 3.4 -- -- -- -- -- -- -- -- -- -- - 4.2 - 0.88 - 2.25 - 8.8 0.88 2.25 8.8 0.00001 0.00001 25 5.0 0.005 0.010 0.015 0.04 0.08 0.13 -- -- -- -- -- -- -- 0.05 0.1 -- 7.5 5.0 10 20 0.20 0.45 0.70 - 1.7 - 0.36 - 0.9 - 2.4 0.36 0.9 2.4 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 0.5 1.0 -- -- 150 300 600 2.0 2.0 2.0 mAdc 3.5 7.0 11 -- -- -- 3.5 7.0 11 2.75 5.50 8.25 -- -- -- 3.5 7.0 11 -- -- -- mAdc Min -- -- -- - 55_C 25_C 125_C Max Min -- -- -- Typ (4.) 0 0 0 Max Min -- -- -- Max Unit Vdc Output Voltage Vin = VDD or 0 "0" Level 0.05 0.05 0.05 -- -- -- 1.5 3.0 4.0 0.05 0.05 0.05 -- -- -- 1.5 3.0 4.0 0.05 0.05 0.05 -- -- -- 1.5 3.0 4.0 Vdc "1" Level Vin = 0 or VDD Input Voltage "0" Level (VO = 4.5 or 0.5 Vdc) (VO = 9.0 or 1.0 Vdc) (VO = 13.5 or 1.5 Vdc) "1" Level (VO = 0.5 or 4.5 Vdc) (VO = 1.0 or 9.0 Vdc) (VO = 1.5 or 13.5 Vdc) Output Drive Current (VOH = 2.5 Vdc) (VOH = 4.6 Vdc) (VOH = 9.5 Vdc) (VOH = 13.5 Vdc) (VOL = 0.4 Vdc) (VOL = 0.5 Vdc) (VOL = 1.5 Vdc) Input Current, Pin 2 or 14 Input Current, Other Inputs Input Capacitance, Pin 2 or 14 Input Capacitance, Other Inputs (Vin = 0) Quiescent Current (Per Package) Q = Low, Q = High Quiescent Current, Active State (Both) (Per Package) Q = High, Q = Low Total Supply Current at an external load capacitance (CL) and at external timing network (RX, CX) (5.) VIL -- -- -- -- -- -- 2.25 4.50 6.75 -- -- -- VOH 4.95 9.95 14.95 4.95 9.95 14.95 5.0 10 15 4.95 9.95 14.95 Vdc Vdc Sink Iin Iin Cin Cin IDD Adc Adc pF pF Adc IDD mAdc IT IT = (3.5 x 10-2) RXCXf + 4CXf + 1 x 10-5 CLf IT = (8.0 x 10-2) RXCXf + 9CXf + 2 x 10-5 CLf IT = (1.25 x 10-1) RXCXf + 12CXf + 3 x 10-5 CLf where: IT in A (one monostable switching only), where: CX in F, CL in pF, RX in k ohms, and where: f in Hz is the input frequency. Adc 4. Data labelled "Typ" is not to be used for design purposes but is intended as an indication of the IC's potential performance. 5. The formulas given are for the typical characteristics only at 25_C. http://onsemi.com 3 MC14538B IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII SWITCHING CHARACTERISTICS (6.) (CL = 50 pF, TA = 25_C) Characteristic Symbol tTLH VDD Vdc 5.0 10 15 tTHL 5.0 10 15 tPLH, tPHL 5.0 10 15 5.0 10 15 tr, tf 5 10 15 5 10 15 5 10 15 tWH, tWL trr 5.0 10 15 5.0 10 15 170 90 80 0 0 0 -- -- -- -- -- -- -- -- -- -- -- -- 300 150 100 250 125 95 -- -- -- 300 1.2 0.4 No Limit 85 45 40 -- -- -- -- -- -- -- -- -- ns 600 300 220 ns 500 250 190 15 5 4 1.0 0.1 0.05 s -- -- -- 100 50 40 200 100 80 ns All Types Typ (7.) 100 50 40 Min -- -- -- Max 200 100 80 ns Unit ns Output Rise Time tTLH = (1.35 ns/pF) CL + 33 ns tTLH = (0.60 ns/pF) CL + 20 ns tTLH = (0.40 ns/pF) CL + 20 ns Output Fall Time tTHL = (1.35 ns/pF) CL + 33 ns tTHL = (0.60 ns/pF) CL + 20 ns tTHL = (0.40 ns/pF) CL + 20 ns Propagation Delay Time A or B to Q or Q tPLH, tPHL = (0.90 ns/pF) CL + 255 ns tPLH, tPHL = (0.36 ns/pF) CL + 132 ns tPLH, tPHL = (0.26 ns/pF) CL + 87 ns Reset to Q or Q tPLH, tPHL = (0.90 ns/pF) CL + 205 ns tPLH, tPHL = (0.36 ns/pF) CL + 107 ns tPLH, tPHL = (0.26 ns/pF) CL + 82 ns Input Rise and Fall Times Reset B Input ms A Input -- Input Pulse Width A, B, or Reset Retrigger Time ns Output Pulse Width -- Q or Q Refer to Figures 8 and 9 CX = 0.002 F, RX = 100 k T 5.0 10 15 5.0 10 15 5.0 10 15 100 [(T1 - T2)/T1] 5.0 10 15 198 200 202 9.3 9.4 9.5 0.91 0.92 0.93 -- -- -- 210 212 214 9.86 10 10.14 0.965 0.98 0.99 1.0 1.0 1.0 230 232 234 10.5 10.6 10.7 1.03 1.04 1.06 5.0 5.0 5.0 ms s CX = 0.1 F, RX = 100 k CX = 10 F, RX = 100 k s Pulse Width Match between circuits in the same package. CX = 0.1 F, RX = 100 k % 6. The formulas given are for the typical characteristics only at 25_C. 7. Data labelled "Typ" is not to be used for design purposes but is intended as an indication of the IC's potential performance. http://onsemi.com 4 MC14538B IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII OPERATING CONDITIONS External Timing Resistance RX CX -- -- 5.0 0 -- -- (8.) k F External Timing Capacitance No Limit (9.) 8. The maximum usable resistance RX is a function of the leakage of the capacitor CX, leakage of the MC14538B, and leakage due to board layout and surface resistance. Susceptibility to externally induced noise signals may occur for RX > 1 M.. 9. If CX > 15 F, use discharge protection diode per Fig. 11. VDD RX 2 (14) CX VDD P1 ENABLE + C2 - 1 (15) N1 4 (12) 5 (11) B RESET 3 (13) VSS Vref1 + C1 - ENABLE Vref2 R Q OUTPUT LATCH S Q 6 (10) 7 (9) CONTROL A QR S RESET LATCH QR R NOTE: Pins 1, 8 and 15 must be externally grounded Figure 1. Logic Diagram (1/2 of DevIce Shown) VDD 500 pF ID RX VSS Vin CX CX/RX Q Q Q Q CL VSS CL CL Vin CL 20 ns 90% 10% 20 ns VDD 0V RX CX VSS 0.1 F CERAMIC A B RESET A B RESET Figure 2. Power Dissipation Test Circuit and Waveforms http://onsemi.com 5 MC14538B VDD INPUT CONNECTIONS RX VSS PULSE GENERATOR PULSE GENERATOR PULSE GENERATOR CX CX/RX Q Q Q Q CL VSS CL CL CL RX CX * CL = 50 pF VSS Characteristics tPLH, tPHL, tTLH, tTHL, T, tWH, tWL tPLH, tPHL, tTLH, tTHL, T, tWH, tWL tPLH(R), tPHL(R), tWH, tWL * Includes capacitance of probes, wiring, and fixture parasitic. NOTE: Switching test waveforms for PG1, PG2, PG3 are shown In Figure 4. Reset VDD VDD PG3 A PG1 VSS PG1 B VDD PG2 PG2 A B RESET A B PG1 = PG2 = PG3 = RESET Figure 3. Switching Test Circuit 50% A tWH B 50% tWL tTHL RESET tTHL 90% 10% tTLH 90% 10% tTHL tTLH 90% 10% tTHL tTHL 90% 10% tPHL 50% tWL tPHL tTLH 50% VDD VDD 90% 10% tPLH 50% T 50% tPHL 50% tPLH 50% tTLH VDD trr 50% Q tPHL Q 50% tPLH 50% 50% Figure 4. Switching Test Waveforms TA = 25C RX = 100 k CX = 0.1 F 1.0 0.8 0.6 0.4 0.2 0 0% POINT PULSE WIDTH VDD = 5.0 V, T = 9.8 ms VDD = 10 V, T = 10 ms VDD = 15 V, T = 10.2 ms NORMALIZED PULSE WIDTH CHANGE WITH RESPECT TO VALUE AT VDD = 10 V (%) RELATIVE FREQUENCY OF OCCURRENCE RX = 100 k CX = 0.1 F 2 1 0 1 2 -4 -2 0 2 4 T, OUTPUT PULSE WIDTH (%) 5 6 7 8 9 10 11 12 VDD, SUPPLY VOLTAGE (VOLTS) 13 14 15 Figure 5. Typical Normalized Distribution of Units for Output Pulse Width Figure 6. Typical Pulse Width Variation as a Function of Supply Voltage VDD http://onsemi.com 6 MC14538B 1000 TOTAL SUPPLY CURRENT ( A) RX = 100 k, CL = 50 pF ONE MONOSTABLE SWITCHING ONLY FUNCTION TABLE Inputs Reset H H 5.0 V 10 V H H H H L A L L H L, H, L X X H L, H, X X Not Triggered Not Triggered Not Triggered Not Triggered L H Not Triggered B H Q Outputs Q 100 VDD = 15 V 10 1.0 0.1 0.001 0.1 1.0 OUTPUT DUTY CYCLE (%) 10 100 Figure 7. Typical Total Supply Current versus Output Duty Cycle TYPICAL NORMALIZED ERROR WITH RESPECT TO 25C VALUE AT VDD = 10 V (%) TYPICAL NORMALIZED ERROR WITH RESPECT TO 25C VALUE AT VDD = 10 V (%) RX = 100 k CX = 0.1 F 2 1 0 -1 -2 RX = 100 k CX = .002 F 3.0 2.0 1.0 0 VDD = 15 V VDD = 10 V VDD = 15 V VDD = 10 V VDD = 5 V - 1.0 - 2.0 - 3.0 VDD = 5.0 V - 60 - 40 - 20 0 20 40 60 80 100 TA, AMBIENT TEMPERATURE (C) 120 140 - 60 - 40 - 20 0 20 40 60 80 100 TA, AMBIENT TEMPERATURE (C) 120 140 Figure 8. Typical Error of Pulse Width Equation versus Temperature Figure 9. Typical Error of Pulse Width Equation versus Temperature http://onsemi.com 7 MC14538B THEORY OF OPERATION 1 3 4 A 2 B 5 RESET Vref 2 CX/RX Vref 1 Vref 1 Vref 2 Vref 1 Vref 2 Vref 1 Vref 2 Q T 1 2 3 T Positive edge trigger Negative edge trigger Positive edge trigger 4 5 T Positive edge re-trigger (pulse lengthening) Positive edge re-trigger (pulse lengthening) Figure 10. Timing Operation TRIGGER OPERATION RETRIGGER OPERATION The block diagram of the MC14538B is shown in Figure 1, with circuit operation following. As shown in Figure 1 and 10, before an input trigger occurs, the monostable is in the quiescent state with the Q output low, and the timing capacitor CX completely charged to VDD. When the trigger input A goes from VSS to VDD (while inputs B and Reset are held to VDD) a valid trigger is recognized, which turns on comparator C1 and N-channel transistor N1 . At the same time the output latch is set. With transistor N1 on, the capacitor CX rapidly discharges toward VSS until Vref1 is reached. At this point the output of comparator C1 changes state and transistor N1 turns off. Comparator C1 then turns off while at the same time comparator C2 turns on. With transistor N1 off, the capacitor CX begins to charge through the timing resistor, RX, toward VDD. When the voltage across CX equals Vref 2, comparator C2 changes state, causing the output latch to reset (Q goes low) while at the same time disabling comparator C2 . This ends at the timing cycle with the monostable in the quiescent state, waiting for the next trigger. In the quiescent state, CX is fully charged to VDD causing the current through resistor RX to be zero. Both comparators are "off" with total device current due only to reverse junction leakages. An added feature of the MC14538B is that the output latch is set via the input trigger without regard to the capacitor voltage. Thus, propagation delay from trigger to Q is independent of the value of CX, RX, or the duty cycle of the input waveform. The MC14538B is retriggered if a valid trigger occurs followed by another valid trigger before the Q output has returned to the quiescent (zero) state. Any retrigger, after the timing node voltage at pin 2 or 14 has begun to rise from Vref 1, but has not yet reached Vref 2, will cause an increase in output pulse width T. When a valid retrigger is initiated , the voltage at CX/RX will again drop to Vref 1 before progressing along the RC charging curve toward VDD. The Q output will remain high until time T, after the last valid retrigger. RESET OPERATION The MC14538B may be reset during the generation of the output pulse. In the reset mode of operation, an input pulse on Reset sets the reset latch and causes the capacitor to be fast charged to VDD by turning on transistor P1 . When the voltage on the capacitor reaches Vref 2, the reset latch will clear, and will then be ready to accept another pulse. It the Reset input is held low, any trigger inputs that occur will be inhibited and the Q and Q outputs of the output latch will not change. Since the Q output is reset when an input low level is detected on the Reset input, the output pulse T can be made significantly shorter than the minimum pulse width specification. http://onsemi.com 8 MC14538B POWER-DOWN CONSIDERATIONS Dx Cx VSS Rx VDD VDD Q Q RESET Large capacitance values can cause problems due to the large amount of energy stored. When a system containing the MC14538B is powered down, the capacitor voltage may discharge from VDD through the standard protection diodes at pin 2 or 14. Current through the protection diodes should be limited to 10 mA and therefore the discharge time of the VDD supply must not be faster than (VDD). (C) / (10 mA). For example, if VDD = 10 V and CX = 10 F, the VDD supply should discharge no faster than (10 V) x (10 F) / (10 mA) = 10 ms. This is normally not a problem since power supplies are heavily filtered and cannot discharge at this rate. When a more rapid decrease of VDD to zero volts occurs, the MC14538B can sustain damage. To avoid this possibility use an external clamping diode, DX, connected as shown in Fig. 11. TYPICAL APPLICATIONS CX RISING-EDGE TRIGGER A B B = VDD RESET = VDD CX A = VSS RX VDD Q B FALLING-EDGE TRIGGER Q RX VDD Q Q Figure 11. Use of a Diode to Limit Power Down Current Surge CX RX VDD RISING-EDGE A TRIGGER B Q Q RESET = VDD CX RX VDD A B FALLING-EDGE TRIGGER RESET = VDD Q Q RESET = VDD Figure 12. Retriggerable Monostables Circuitry Figure 13. Non-Retriggerable Monostables Circuitry NC Q Q CD VDD VDD NC NC A B Figure 14. Connection of Unused Sections http://onsemi.com 9 MC14538B PACKAGE DIMENSIONS -A- 16 9 PDIP-16 P SUFFIX PLASTIC DIP PACKAGE CASE 648-08 ISSUE R B 1 8 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. DIM A B C D F G H J K L M S INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0_ 10 _ 0.020 0.040 MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0_ 10 _ 0.51 1.01 F S C L -T- H G D 16 PL SEATING PLANE K J TA M M 0.25 (0.010) M -A- SOIC-16 D SUFFIX PLASTIC SOIC PACKAGE CASE 751B-05 ISSUE J NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. MILLIMETERS MIN MAX 9.80 10.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.386 0.393 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.229 0.244 0.010 0.019 16 9 -B- 1 8 P 8 PL 0.25 (0.010) M B S G F K C -T- SEATING PLANE R X 45 _ M D 16 PL M J 0.25 (0.010) TB S A S DIM A B C D F G J K M P R http://onsemi.com 10 MC14538B PACKAGE DIMENSIONS SOIC-16 DW SUFFIX PLASTIC SOIC PACKAGE CASE 751G-03 ISSUE B D 16 M 9 A q NOTES: 1. DIMENSIONS ARE IN MILLIMETERS. 2. INTERPRET DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 1994. 3. DIMENSIONS D AND E DO NOT INLCUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 5. DIMENSION B DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.13 TOTAL IN EXCESS OF THE B DIMENSION AT MAXIMUM MATERIAL CONDITION. MILLIMETERS MIN MAX 2.35 2.65 0.10 0.25 0.35 0.49 0.23 0.32 10.15 10.45 7.40 7.60 1.27 BSC 10.05 10.55 0.25 0.75 0.50 0.90 0_ 7_ H B 1 8 16X B TA S B B S h X 45 _ M 8X 0.25 E 0.25 M A1 14X e SEATING PLANE DIM A A1 B C D E e H h L A L T C q TSSOP-16 DT SUFFIX PLASTIC TSSOP PACKAGE CASE 948F-01 ISSUE O 16X K REF 0.10 (0.004) 0.15 (0.006) T U S M TU S V S K K1 16 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH. PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. DIM A B C D F G H J J1 K K1 L M MILLIMETERS MIN MAX 4.90 5.10 4.30 4.50 --- 1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.18 0.28 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0_ 8_ INCHES MIN MAX 0.193 0.200 0.169 0.177 --- 0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.007 0.011 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0_ 8_ 2X L/2 9 J1 B -U- L PIN 1 IDENT. 1 8 SECTION N-N J N 0.25 (0.010) 0.15 (0.006) T U S A -V- N F DETAIL E C 0.10 (0.004) -T- SEATING PLANE H D G DETAIL E http://onsemi.com 11 CCC EE CCC EE M -W- MC14538B PACKAGE DIMENSIONS SOEIAJ-16 F SUFFIX PLASTIC EIAJ SOIC PACKAGE CASE 966-01 ISSUE O LE Q1 E HE 1 8 16 9 M_ L DETAIL P Z D e A VIEW P NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5. THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD TO BE 0.46 ( 0.018). DIM A A1 b c D E e HE L LE M Q1 Z MILLIMETERS MIN MAX --- 2.05 0.05 0.20 0.35 0.50 0.18 0.27 9.90 10.50 5.10 5.45 1.27 BSC 7.40 8.20 0.50 0.85 1.10 1.50 10 _ 0_ 0.70 0.90 --- 0.78 INCHES MIN MAX --- 0.081 0.002 0.008 0.014 0.020 0.007 0.011 0.390 0.413 0.201 0.215 0.050 BSC 0.291 0.323 0.020 0.033 0.043 0.059 10 _ 0_ 0.028 0.035 --- 0.031 c b 0.13 (0.005) M A1 0.10 (0.004) ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION NORTH AMERICA Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com Fax Response Line: 303-675-2167 or 800-344-3810 Toll Free USA/Canada N. American Technical Support: 800-282-9855 Toll Free USA/Canada EUROPE: LDC for ON Semiconductor - European Support German Phone: (+1) 303-308-7140 (M-F 1:00pm to 5:00pm Munich Time) Email: ONlit-german@hibbertco.com French Phone: (+1) 303-308-7141 (M-F 1:00pm to 5:00pm Toulouse Time) Email: ONlit-french@hibbertco.com English Phone: (+1) 303-308-7142 (M-F 12:00pm to 5:00pm UK Time) Email: ONlit@hibbertco.com EUROPEAN TOLL-FREE ACCESS*: 00-800-4422-3781 *Available from Germany, France, Italy, England, Ireland CENTRAL/SOUTH AMERICA: Spanish Phone: 303-308-7143 (Mon-Fri 8:00am to 5:00pm MST) Email: ONlit-spanish@hibbertco.com ASIA/PACIFIC: LDC for ON Semiconductor - Asia Support Phone: 303-675-2121 (Tue-Fri 9:00am to 1:00pm, Hong Kong Time) Toll Free from Hong Kong & Singapore: 001-800-4422-3781 Email: ONlit-asia@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-8549 Phone: 81-3-5740-2745 Email: r14525@onsemi.com ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. http://onsemi.com 12 MC14538B/D |
Price & Availability of MC14538B
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |